HOW TO INSTALL A BATHTUB

How to Install a Bathtub

How to Install a Bathtub

Blog Article

Get Quote Now

We have unearthed the article on Installing A Bathtub directly below on the net and felt it made perfect sense to relate it with you here.


A Step-by-Step Guide to Installing a Bathtub
Mounting a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard project. If the old tub is readily available, the job can move immediately; if you need to open up a wall surface to get rid of the old tub and position the new bathtub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to leave the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the task and are comfortable attempting it. Rather than hiring a professional to take control of a halfway-completed project, it is better to think about employing one before you begin. Possibilities are you may need a specialist plumber to make tube links.
This short article will aid you mount a brand-new bath tub in your shower room if you have actually currently bought a brand-new tub and also do not require to alter the arrangement of your previous water system pipelines.
Your devices as well as product checklist ought to consist of the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of getting rid of the existing taps can be fairly troublesome as a result of the restricted accessibility that is typically the case.
    Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, use the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
    Prior to moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the existent supply pipelines.
    If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next, place the tap in the placing hole in the bath/basin making sure that the washers remain in location between the faucet and the sink. Safeguard the tap in position with the manufacturer offered backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind should be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

    Setting up the Bath tub


    Using both wood boards under its feet, place the tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small points.
    The following goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub up until the level reads level.
    To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
    Turn on the water and also check all joints as well as new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally examine the overflow electrical outlet and the normal outlet for leaks.
    Ultimately, deal with the bathroom paneling as described in the producer's instruction manual. Tiling as well as sealing around the bathtub ought to wait up until the tub has actually been utilized at the very least when as this will certainly resolve it right into its last placement.

    Preparing for the Installation


    Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to stop pressure on the bath tub.
    Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the provided washers.
    Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final position.

    Tiling Around the Bath tub


    In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and the tiling, bring about problems with dampness as well as possible leakages to the ceiling below.
    You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into account this motion prior to sealing.
    Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    I was brought to that article about Tools You Need to Install a New Bathtub from an acquaintance on another web property. Do you know about another individual who is involved in the niche? Take a moment to share it. Thank-you for your time invested reading it.




    Visit My Site


    Report this page